Subscribe Contribute Advertise Facebook Twitter Instagram Forums Newsletter
help! can't fix my pucker
Display Avatars Sort By:
Thomas C
(wgonfan) - F
help! can't fix my pucker on 03/23/2014 17:24:19 MDT Print View

Well.. I guess its a pucker. The stitches (straight, 6per inch) on my tie out reinforcements go slack and pucker up on top when tied out. Mpmy stitches look good otherwise and as far as I can tell my tension is balanced out as good as its going to get. I'm using an older sears 1403 zigzag machine, silnylon tarp with 200d reinforcement material and Buyer tera 80 thread. Any idea how I can correct this? I've tried adding sticthes and increasing my bottoms tension, which helped but made sewing a nightmare. I'm sure the is something I'm over looking.

Thomas C
(wgonfan) - F
zigzag on 03/23/2014 17:45:49 MDT Print View

I also tried a zigzag stitch which did not help. Again my eyes suck but under a magnify glass the sticthes look good and only pucker when pulled tight against the stictch. Also, I only have reinforcement on one side.

peter vacco
(fluff@inreach.com) - M

Locale: no. california
Re: zigzag on 03/23/2014 18:31:33 MDT Print View

you might coat those particular stiches with mcnett to keep them from doing that nasty thing.
are all the other stitches on the thing OK ? just these ones getting puller real hard ?
thread's going to move form one side to the other in sylnylon. it;s terrible slippery stuff.

John S.
(jshann) - F
Re: help! can't fix my pucker on 03/23/2014 19:03:10 MDT Print View

Your gonna need a urologist.

Doug I.
(idester) - MLife

Locale: MidAtlantic
Re: Re: help! can't fix my pucker on 03/23/2014 19:08:18 MDT Print View

"Your gonna need a urologist."

For kissing advice? I don't know John, that seems a bit strange.....

David Scheidt
(dscheidt) - F
sandwich on 03/23/2014 19:41:58 MDT Print View

Consider a sandwich of reinforcement on both sides of the sil. On the other hand, I'm not sure how much your puckering matters. Is it going to leak?

Thomas C
(wgonfan) - F
sandwich on 03/24/2014 07:46:15 MDT Print View

"Consider a sandwich of reinforcement on both sides of the sil"

I've tried everything else & I recon this is the only option. I did notice that the ridgeline & side pulls do not stretch & pucker the same away so I think it just has to do with going against the "grain" of the sil.

Marko Botsaris
(millonas) - F - MLife

Locale: Santa Cruz Mountains, CA
Re: Re: help! can't fix my pucker on 03/24/2014 08:53:27 MDT Print View

"Your gonna need a urologist."

More like a proctologist I was thinking. Weird the images you can get from a mere thread title if you are as warped as Doug and I.

Edited by millonas on 03/24/2014 08:53:58 MDT.

Jon Holthaus
(t25hatch) - M
Needle Size? on 03/24/2014 09:40:47 MDT Print View

What size needle are you using for an tera 80 thread? Typically an 80wt thread requires a size 18 needle and is used for thicker fabrics. I'd suggest switching to a smaller say 46wt 100% poly thread with a size 14 needle will fix it. If you're going through some thicker material at the tieout points, I wouldn't go beyond a 69wt thread with size 16 needle. I'm no expert but I have had good results with this set up.

Also as many have recommended a roller presser foot is a dream when sewing silnylon, not sure if you've look into those either.

Edited by t25hatch on 03/24/2014 09:42:27 MDT.

Sam Haraldson
(sharalds) - MLife

Locale: Gallatin Range
help! can't fix my pucker on 03/24/2014 10:29:21 MDT Print View

What Jon said above, sounds like too large a needle to me. Also adjusting your thread tension and doing some tests on scrap fabric could enlighten you as well.

Thomas C
(wgonfan) - F
needle on 03/24/2014 10:46:20 MDT Print View

I use a #9 & #12 needle depending on my mood.

Thomas C
(wgonfan) - F
Tension on 03/24/2014 10:50:48 MDT Print View

I do practice & adjust & recheck my tensions on scrap, its as close to perfect as I can get it with my machine & my eyes.

Thomas C
(wgonfan) - F
Thread / Needle on 03/24/2014 11:23:14 MDT Print View

After doing some reading this morning I think Jon is right... I need smaller thread or a bigger needle. I prefer smaller holes so I'm going to try & find some smaller thread today & see if that has any effect.

Thomas C
(wgonfan) - F
Fixed on 03/25/2014 10:45:12 MDT Print View

First, I was wrong... That Tera 80 is actually 35wt thread & not 80wt thread as someone suggested.

I fixed my puckering issue by stitching radially out from the corner, with the grain.

robert van putten
(Bawana) - F

Locale: Planet Bob
To Have and Have Not on 03/25/2014 12:19:36 MDT Print View

"You know you don't have to act with me, Steve. You don't have to say anything, and you don't have to do anything. Not a thing. Oh, maybe just whistle. You know how to whistle, don't you, Steve?. You just put your lips together and blow."

Good advice from Lauren Bacall to Humphery Bogart.

Ain't gonna help the sewing any but might brighten yer day!