Lite Trail Solid Fuel System
Display Avatars Sort By:
Ian B.
(IDBLOOM) - MLife

Locale: PNW
Lite Trail Solid Fuel System on 12/17/2013 00:36:27 MST Print View

I purchased this cook system about six months ago when they offered a limited run. The mug I received has the Toaks branding on it; from my understanding, this is not typical but I assume it's basically the same mug everyone else received. If someone knows differently then please correct me.

One of the small nits I had to pick with the V2 system was the windscreen which is spot welded together and does not allow for the best use of space within the pot.

.Before

I ordered the V3 windscreen which arrived today. As you can see, this fits much better.

.After

I've added a set of Hot Lips and a Gossamer Gear Warm Sak to this kit. The Warm Sak works fine and I don't care to waste my time or fuel to see whether or not it may work slightly better or worse than my reflectix cozy. It is a snug fit but it works.

http://gossamergear.com/warm-sak.html
http://tinyurl.com/pgpfyq8

.Warm Sak

The cuben fiber stuff sack is now in use as my ditty bag. My system including the Warm Sak, Solid Fuel System minus cuben sack, mini bic, and Hot Lips weighs in at 4.4 oz. At that weight, I don't feel too compelled to replace the lid with foil or remove the handles.

Since 99% of my trail cooking is accomplished by boiling water, this is my go-to kit. My daughter and I used this on our Wonderland Trail section hike as a two person system simply by adding an extra mug for her to use and by rehydrating our food in freezer bags.

Ryan Smith
(ViolentGreen) - F

Locale: Southeast
Re: Lite Trail Solid Fuel System on 12/17/2013 06:17:27 MST Print View

Nice. I've been fighting the urge to get V3 for a couple weeks now.

Ryan

Clayton Mauritzen
(GlacierRambler) - F - M

Locale: NW Montana
Re: Re: Lite Trail Solid Fuel System on 12/17/2013 07:27:44 MST Print View

I have V1, and really loved it on the trail last year. However, V3 appears to have corrected all of my minor complaints about V1--lack of handles, thicker Ti foil. As soon as Jhaura released the parts individually, I upgraded my V1 to V3.

I'm excited to use it again this year.

Ken Thompson
(kthompson) - MLife

Locale: Behind the Redwood Curtain
Re: Lite Trail Solid Fuel System on 12/17/2013 08:42:39 MST Print View

Save some dough and buy your pot direct

http://toaksoutdoor.com/titanium550mlpot.aspx $29.95 vs. $44.95

William Chilton
(WilliamC3) - MLife

Locale: Antakya
Re: Re: Lite Trail Solid Fuel System on 12/17/2013 09:27:26 MST Print View

Or spend more dough (at LiteTrail) and save 16 grams (72g vs 88g).

Chad B
(CenAZwalker) - F

Locale: Southwest
Re: Re: Lite Trail Solid Fuel System on 12/17/2013 09:40:24 MST Print View

Yes, the LiteTrail pots are made by Toaks but they are of a thinner Ti than the regular Toaks models.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Re: Re: Lite Trail Solid Fuel System on 12/17/2013 10:07:09 MST Print View

Hopefully someone will have the thinner one at the GGG for comparison but I'm pretty happy with the kit and don't see any reason to swap out the mug.

William Chilton
(WilliamC3) - MLife

Locale: Antakya
Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/17/2013 10:17:08 MST Print View

Ian, I think you already have the thinner one since you got it from LiteTrail.
Edited to add: I just reread your OP. The LiteTrail pots are branded Toaks, but as I understand it, they are specialy made for LiteTrail and are not the same as the standard Toaks 550ml pot.

Edited by WilliamC3 on 12/17/2013 10:18:55 MST.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/17/2013 10:26:00 MST Print View

Maybe but mine has the Toaks branding on it which is why I have my doubts. He did a second run of the V2s and possibly used the regular Toaks mug to fill the order. Again, I'm very happy with this kit and don't have any complaints or wish to swap it out. I'll weigh the mug solo later to determine if it's the thinner one or not.

Despite Craig's claims that my 550ml mug is for child sized portions only, I think it's perfect for me as I can warm up a pint of water and still have a little room to spare to avoid boil-over. If I was actually looking to do any real cooking in the pot then obviously I'd need something bigger but freezer bag cooking is fine for me.

William Chilton
(WilliamC3) - MLife

Locale: Antakya
Toaks branding on 12/17/2013 10:45:16 MST Print View

I have the pot from version 1. It also has the Toaks branding, but weighs 41 grams (no handles on version 1). I would be interested to see what yours weighs but I expect you have a thinner walled one too.
We find 550 ml to be the perfect size for 2, but we share one meal while the water is boiling for the second.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Toaks branding on 12/17/2013 11:05:51 MST Print View

I may have misunderstood Jhaura's comment from a previous thread:

"It will be in stock before the holidays. More news to follow on Nov 1. Our pot is not the same as the Toaks. Our stove is modded for snug fit on our pot only, it is not marketing, it's design and really does work, you can mod one yourself, but the ti is hard to grind. We will have most of the pieces avail. individually. ~J"

http://www.backpackinglight.com/cgi-bin/backpackinglight/forums/thread_display.html?forum_thread_id=83139

I’ll post the weight later tonight and hopefully that answer my question.

"We find 550 ml to be the perfect size for 2, but we share one meal while the water is boiling for the second."

What we do is share a "two person" meal (with olive oil added) which typically requires two cups of water and add other non-cook items (Fritos, dried fruit, jerky, etc) to round out the meal and to add some calories. We typically graze throughout the day so I'm not necessarily ravenous by dinner time.

Edited by IDBLOOM on 12/17/2013 11:07:09 MST.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Re: Re: Lite Trail Solid Fuel System on 12/17/2013 23:24:02 MST Print View

"Or spend more dough (at LiteTrail) and save 16 grams (72g vs 88g)."

I just weighed my pot with lid at 70g / 2.5oz.

.Lite Trail / Toaks Mug

Edited by IDBLOOM on 12/17/2013 23:25:41 MST.

Nick Gatel
(ngatel) - MLife

Locale: Southern California
Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/18/2013 01:32:30 MST Print View

I upgraded mine from V1 too. The new pot with lid is 70 grams on my bilingual scale.

I am still going back and forth between my Caldera GVP and the LiteTrail system. I have been mostly taking the GVP unless space in my pack is tight and I need to cram in the stove. It is a conundrum between the two.

We'll see if the handles and improved screen make the LiteTrail more attractive to me. It was already 4 grams heavier than the GVP. I haven't bothered to figure out how much heavier the new pot and screen will make the kit -- really doesn't matter, I'll take the one that works the best. Will be trying out the new pot in a few days.

For anyone who is interested, here is a comparison I did in May. LiteTrail vs Caldera GVP

Both are excellent set-ups. It's good we have choices :)

Chad Poindexter
(Stick) - F

Locale: Wet & Humid Southeast....
Re: Lite Trail Solid Fuel System on 12/18/2013 08:18:37 MST Print View

Yes, as has been noted, Toaks actually make the LiteTrail cook pots for Jhaura, which is why they are branded "Toaks." But no, the pots sold from Toaks are different from the ones that are sold by LiteTrail. The ones they make for Jhaura is made from a thinner ti, which means they do weigh less. I have the Toaks 375 ml mug and it does have a slightly thicker feel to it.

And as far as weights are concerned, my LiteTrail 550 ml pot only (without handles) weighs 1.4 oz. The Toaks 375 ml mug with handles weighs 2.2 oz. Of course it would be more of a fair match had the handles been removed from the mug, however, the handles I removed from another ti cook pot sometime back (which are actually a bit larger than these on the Toaks mug) weigh 0.5 oz. So, this would make the 375 ml Toaks mug without handles around 1.7 oz, which is heavier than the 550 ml pot by 0.3 oz, and has a lesser volume.

As for price, that is up to the person to decide if it is worth it to them. From my understanding, it takes a little more care to work with thinner ti, which increases the price. Of course I don't know this for sure, however, it is a safe bet to figure that as things get lighter in the backpacking world, the prices go up.

Me myself, I love Jhaura's kit, and is probably my favorite cook kit. I have the original version 1. No handles, super thin ti windscreen and uses paper clips to hold it together, and I have no reason to change it. I love the way it works, how it all packs together, and that it is as light as I can get it. My ENTIRE cook kit weighs 3.9 oz (which includes spoon, bic, towel, parts to use pot as mug, etc...)

It is cool that Jhaura does offer the different pieces of his kit separately though for others that may want to "upgrade" their older kits, or piece together their own.

Edited by Stick on 12/18/2013 08:19:18 MST.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Re: Lite Trail Solid Fuel System on 12/18/2013 08:27:27 MST Print View

Nice article Chad. I picked up the Hot Lips idea from one of your videos so thanks for that. That carbon fiber lid is pretty tempting...

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Re: Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/18/2013 08:43:50 MST Print View

Nick, a quote from your site: "Typically in the field I use at least 1/2 of a 14 gram Esbit cube to heat 16 ounces of water. But it is not unusual to get two pots of heated water from a single cube.
Lets start with the Caldera system. It consists of"

32 ounces of heated water on one cube is fantastic. Even if it doesn't get to a boil, it's still fantastic. It seems like we should be seeing a shift from alcohol to esbit this coming season, don't we all agree?

All of you that are using these ti systems, how do you pick-up and hold onto the hot handles?

Chad Poindexter
(Stick) - F

Locale: Wet & Humid Southeast....
Picking up a hot pot on 12/18/2013 08:54:26 MST Print View

Dan,

I don't use handles on my 550 ml pot. When I am boiling water for a meal, the pot is filled up to about half, or three quarters of an inch from the top. When the water is to the point that I need it to be (not quite boiling, but close) I just use my LiteLoad towel folded longways to grab the pot near the top and lift it off. Also, I use 4 g Esbit tabs, so am able to choose as much fuel as I want so that by the time my water is to the temp I want it at, the fuel is almost gone anyway, which means the flames are not an issue when grabbing the pot off like this.

When heating water for coffee/cocoa/tea, the pot is only about half filled. Since the water is no where near the top, I can simply grab the pot off with my bare fingers, then I slip it into the DIY cozy I made for the pot when using it as a mug.

For an idea, check out this video around 11:45 or so:

LiteTrail Cook Kit video

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Re: Re: Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/18/2013 09:08:54 MST Print View

"All of you that are using these ti systems, how do you pick-up and hold onto the hot handles?"

If it's too hot to pick up with my bare hands, then with a bandana.

"32 ounces of heated water on one cube is fantastic. Even if it doesn't get to a boil, it's still fantastic. It seems like we should be seeing a shift from alcohol to esbit this coming season, don't we all agree?"

32 ounces of sufficiently heated but not quite boiling water is my experience with this too.

I love Esbit and use it for the very large majority of my backpacking.

The pros:

lightweight
nothing to leak. Pulverize it and it'll still work.
emergency fire starter

The cons to me:

More expensive than alcohol
For someone who's through hiking, I presume much more difficult to find when making resupply runs.

For me this is my go-to kit but when I start my PCT through hike in 8.5 years from now, I’d probably bring my TD sidewinder paired up with my Evernew 600ml pot and my handy dandy super high speed low drag high testosterone low drama all killer no filler gangster of love starlyte stove.

Edited by IDBLOOM on 12/18/2013 09:13:42 MST.

Nick Gatel
(ngatel) - MLife

Locale: Southern California
Re: Re: Re: Re: Re: Re: Lite Trail Solid Fuel System on 12/18/2013 10:26:46 MST Print View

"32 ounces of heated water on one cube is fantastic. Even if it doesn't get to a boil, it's still fantastic. It seems like we should be seeing a shift from alcohol to esbit this coming season, don't we all agree?

All of you that are using these ti systems, how do you pick-up and hold onto the hot handles?"

Contrary to what I expected, the Caldera Cone beer can pot (tall, small diameter) is more efficient than the LiteTrail pot (short, wide diameter) by about 30% in fuel consumption.

I haven't used v3 of the pot yet. But with my MSR Titan pot or Snow Peak Ti pot I grab the handle with my bandana or am wearing a glove liner when it is cold out.

The Caldera GVP system is lighter and more efficient. Sometimes I would rather have the larger pot, as I can pour hot water into my freezer bag meal and while it is "cooking" I can immediately enjoy a hot beverage -- much more efficient use of my kitchen time, and welcomed in colder weather.

The LiteTrail packs down to a much smaller package, and the pot is more robust.

Either system is a good choice.

I have been using Esbit almost exclusively for the past 4 years. If I need to re supply in a town, I bring alcohol; Esbit is too difficult to find. If I am flying to my destination I bring the alcohol stove unless I know Ahead of time I can find Esbit.

Steven Paris
(saparisor) - M

Locale: Pacific Northwest
Modified LiteTrail System on 12/18/2013 11:18:39 MST Print View

Here's my latest take on a LiteTrail 550mL pot alcohol kit (either Heet or Kleen Strip denatured). I haven't made the switch to Esbit; I know I should try it, but just haven't yet. I know this is a thread about solid-fuel but I thought I show the pot in yet another configuration. I wanted to see how it did with a tall wind-screen, with maybe some of the benefits of a Caldera Cone, funneling the heat up around the pot.

LiteTrail 550mL pot, RL carbon lid, Zelph Starlyte stove + pot stand, QiWiz Tall windscreen, ground protector/reflector, cuben Litetrail sack (not shown):

LiteTrail system

My only issue is the handles. I decided to keep the handles, but removed the gray heat-resistant coating. My idea is to have the handles folded up while boiling, like in the photo below. They are too hot to immediately use to remove the pot, but cool down quickly and then I can use the pot as a mug if I want. Alternatively, I can leave a gap in the windscreen where the handles could stick out, but I haven't tried that yet to see how it affects the system.

Ready to boil:

LiteTrail system 2

I have some weight and boil-time numbers I'll have to add later.