StarLyte Burner With Cap
Display Avatars Sort By:
Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
StarLyte Burner With Lid on 01/08/2013 19:03:59 MST Print View

StarLyte Burner only with lid.

Lid fits nice and tight so fuel does not evaporate.

Burner has 1.5 ounce fuel capacity. Holds 1oz. fuel in suspension, will not spill out if accidentally tipped over. Great safety factor.

Buy several, fill them at home with caps on and go hiking. No need to carry a fuel bottle.

Total cost is $13.00 and that includes the shipping.

You get 1 burner and 1 lid

http://www.woodgaz-stove.com/starlyte-burner-with-lid.php

Edited by zelph on 05/31/2013 05:36:13 MDT.

Dustin Judd
(ddujnitsud) - F
You're out on 01/11/2013 16:50:56 MST Print View

The webpage says you are out of stock. Are you taking back orders and if so how long? I've tried most other alky stoves, but this one I have not.

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
StarLyte Burner With Cap on 01/11/2013 21:39:44 MST Print View

I sold out the same day I listed them. I'll have a hundred made by Monday. I'll have the paypal buttons up again on Monday. I'll also have some made that will burn better in a caldera cone. The top wil be reduced in diameter.

Dustin Judd
(ddujnitsud) - F
dimensions? on 01/12/2013 15:13:56 MST Print View

I am hoping to use mine inside my Emberlit or El mini wood burner. Can you post the dimensions of each please?

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Re: dimensions? on 01/12/2013 16:10:37 MST Print View

They are 2" in diameter and 1" in height.

Fuel capacity is 1.5 ounces.

Dan Durston
(dandydan) - M

Locale: Cascadia
Starlyte on 01/12/2013 18:42:18 MST Print View

Awesome stuff. Nice to see people are picking these up.

Jacob Smith
(Wrongturn) - MLife

Locale: The Soda
Re: on 01/12/2013 18:49:17 MST Print View

Ordered mine last week. Hoping to put it to use on my section hike over spring break.

Mark Rash
(markrvp) - M

Locale: North Texas
Choosing a stove on 01/13/2013 16:52:05 MST Print View

Hi Dan:

Is the purpose of this model to have spares for a full Starlyte Burner that has the pot stand? So on a trip you'd take one of these fully fueled instead of a fuel bottle and just swap out stoves? If I buy one of these, I would need to fashion some type of pot stand, right?

You have so many neat stoves, but I never know why I should use one instead of another. If you have some spare time I would really appreciate a comparison chart on your website of your different stoves as well as recommendations for picking a stove.

Thanks!

Derrick White
(miku) - MLife

Locale: Newfoundland & Labrador, Canada
Where to Order on 01/13/2013 19:02:01 MST Print View

Dan - where can I order the one that works in The Caldera Cone? Thanks Derrick

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Modified StarLyte on 01/14/2013 13:59:10 MST Print View

I just finished making a batch of 100 StarLyte burners. 50 original and 50 modified to burn in confined space as under the Calder Cone.

I know the modified one worked for me a couple of years ago when I made a cone shaped windscreen to surround a kmart grease pot supported by a StarLyte stove with the burner modified. The windscreen being wider at it's base allowed for less radiant heat to reach the stove. The top portion of the windscreen was held to within 1/8" of the pot. Keep in mind the windscreen does not support the pot as in the Caldera Cone. The windscreen and stove fit nicely inside the grease pot that is capable of holding 4 cups of water. There is a thread over at Whiteblaze that I created to show the set-up and will post it here later.

I have the two different burners now listed at my stove store. I was a little bit disturbed to find that my material costs have risen to a point that I had to increase my prices.


In the photo below the burner on the left has been modified to reduce the rate of burn. The fact that the fuel is held in suspension, in my opinion, makes it perfom in a more stable fashion in an enclosed windsreen.

<center>

</center>

Mark, yes you need to fashion a pot support 2 inches tall. The pot needs to be 1" from the top of the burner. I'll put the comparison chart towards the top of my list of things to do.

Derrik, the new Modified burner will work in the Caldera Cone. It is availble now at:

http://www.woodgaz-stove.com/starlyte-burner-with-lid.php

Edited by zelph on 01/18/2013 12:05:31 MST.

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Re: Modified StarLyte on 01/15/2013 08:04:17 MST Print View

These two videos show how the modified burner works with a windscreen

<center>


</center>

Mole J
(MoleJ) - F

Locale: UK
Why modified? on 01/15/2013 10:35:44 MST Print View

Hi Dan
I'm not totally clear on why the modified Starlyte is better for using with a cone?
I'm guessing fuel efficiency?

I have been using my first standard Starlyte for over 2 years only with my MSR Ti kettle and homemade split cone with no perceived issues re boil times with acceptable fuel efficiency. Is the modified version more fuel efficient because it burns slower?

Does this mean boil time is increased at all?

thanks

Mole

Edited by MoleJ on 01/15/2013 10:40:55 MST.

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Re: Why modified? on 01/15/2013 11:49:09 MST Print View

I thouroughly tested the original StarLyte stove with the cone shaped windscreen and the kmart grease pot. I kept windscreen configuration as you see it in the videos. I decreased the surface are of the StarLyte burner in small increments until I achieved the goal of 2 cups boiled with 1/2 ounce of fuel. Those tests were performed under ideal conditions. The pot was made of aluminum which conducts heat most efficiently. With the original Starlyte I was not able to get a boil with 1/2 ounce of fuel. So I was looking for the fuel efficiency. Each time I made a change in the burner I tested it 3 times to make sure if there was a change in fuel efficiency. It takes a very long time to do the testing because of having to wait for the stove, windscreen, pot and test surface(table) to cool off.


Yes, cooking time increases and so does fuel efficiency. "Tony" here on BPL instilled in my mind that slow is good. In the video above I think it took 9 min. to get the boil with the Ramen noodles in the pot.

Mole, Under ideal conditions can you boil 2 cups of water with 1/2 ounce of fuel
using your split cone and Ti Kettle?

Edited by zelph on 01/15/2013 16:23:49 MST.

Richard Scruggs
(JRScruggs) - MLife

Locale: Oregon
Re: StarLyte Burner With lID on 01/15/2013 13:04:42 MST Print View

How do you snuff out the flame on the Starlyte Burner in order to save unused fuel?

If the lid is plastic and it's laid on top of the burner to snuff the flame, seems like the lid perhaps might get damaged (melted) with repeated snuffings.

Bob Gross
(--B.G.--) - F

Locale: Silicon Valley
Re: Re: Why modified? on 01/15/2013 13:12:13 MST Print View

"With the original Starlyte I was not able to get a boil with 1/2 ounce of fuel. It may have boiled with .07 oz. or a little bit more or less."

Dan, that is probably not what you meant to write.

--B.G.--

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Modified StarLyte Burner on 01/15/2013 16:18:34 MST Print View

Richard, that is correct, the lid will melt. Get your face close to the burner and give a good "poooof" not a wimpy puff :-)

Bob, you're right. Not what I wanted to say. I deleted the entire sentence. Thanks for the heads up. :-)

Edited by zelph on 01/15/2013 16:25:47 MST.

Dan Durston
(dandydan) - M

Locale: Cascadia
Starlyte on 01/15/2013 16:26:13 MST Print View

"How do you snuff out the flame on the Starlyte Burner in order to save unused fuel?"

I use my pot lid (even though it's carbon fiber) and just set it on the stove. The flame goes out in a matter of a second, so the lid doesn't really get warm. Any means of cutting off the oxygen works well - gently set your pot directly on it, use a lid, cover it with a fry pan lid or ti mug (takes a couple seconds) or just give it a good puff.

And yes, do wait a little bit before slapping the plastic lid on there as you can melt it a bit if you toss it on in the first 60 seconds or so.

Richard Scruggs
(JRScruggs) - MLife

Locale: Oregon
Re: Starlyte on 01/15/2013 18:50:17 MST Print View

Thanks for the info about snuffing the burner, Dan Y and Dan D.

Another question: Dany Y, Dan D, (or anyone else), have you tried using a StarLyte Burner (modified, unmodified, or both) in a Clikstand setup (stand w/windscreen)?

Here's a link to a diagram of the Clikstand specs at Clikstand's website:

http://www.clikstand.com/specs_cs2.html

Dan Yeruski
(zelph) - MLife

Locale: www.bplite.com
Re: Re: Starlyte on 01/15/2013 20:10:12 MST Print View

I have not used a clickstand with the StarLytes. According to the Clickstand sites' specs, the burner should be placed on the shelf that supports the Trangia. The top of the Starlyte should be 1" away from the pot.

Richard Scruggs
(JRScruggs) - MLife

Locale: Oregon
StarLyte Burner and Clikstand on 01/15/2013 20:47:07 MST Print View

Re setting the StarLyte on the Clikstand shelf, two issues seem to arise.

First, the hole in the center of the Clikstand shelf is 3" diameter since it's designed to suspend a Trangia burner, but the Starlyte Burner's diameter is only about 2" (I believe) -- although one way to support the StarLyte would be to use the "solid fuel adapter" accessory (see link below at Clikstand's website) that would keep the StarLyte Burner from setting too low.

http://www.clikstand.com/p_accessories.html

The second issue then comes into play -- the StarLyte setting on the "solid fuel adapter" would seem to be somewhat less than an inch to the bottom of the pot.

Based on the Clikstand specs, the distance from SkyLyte's burner to the pot's bottom might be as litte as half an inch given the SkyLyte's 1" height and the Clikstand's overall height of about 3".

Don't know exact height from the Clikstand's shelf to the pot's bottom, but it looks about half the overall 3" height of the stand (or 1 1/2"). If that's the case, then the burner-to-pot distance using a StarLyte Burner set on the shelf may be only half-an-inch. Probably too close.

The reason I'm curious about using the StarLyte Burner (modified or unmodified) with the ClikStand is the StarLyte Burner would afford a lighter burner option for use with the Clikstand. The only alcohol burners that the Clikstand appears to be designed to fit well is the Trangia burner and (with an adapter shown at the above link) the Evernew Ti burner.