MYOG - Reflectix Pot Cozy
Display Avatars Sort By:
Denis Hazlewood
(redleader) - MLife

Locale: Luxury-Light Luke on the Llano Azul
MYOG - Reflectix Pot Cozy on 12/24/2008 13:14:21 MST Print View

I have had several PMs regarding the Reflectix pot cozies that I've made for my BPL SUL pots. While eating from my pot I have noticed that the sides of the cozy are warm. It occurred to me that I might lengthen the sides of the top to provide a double layer, increasing the efficiency.

I decided to make a new lid for my Firelite SUL1100 cozy and take photos of the process. Making the cozy body uses the same process, so you can see how it's done.

Firelite SUL1100 with Reflectix Cozy - original short lid
Firelite SUL1100 with original, short lid, cozy.

SUL1100 and original cozy bottom
SUL1100 and original cozy bottom.

Reflectix and required tools
Reflectix and required tools.

Measure cozy sidewall and allow for thickness of top
Measure cozy sidewall and allow for thickness of top.

Use straightedge to mark cut line.
Use straightedge to mark cut line.

Roll Reflectix around pot/cozy and mark for cutting length.
Roll Reflectix around pot/cozy and mark for cutting length.

Place Reflectix Tape allowing for 1/2 tape width overlap.
Place Reflectix Tape allowing 1/2 tape width for join.

After fastening ends of Reflectix at outside joint, tape inside of joint.
Next, tape inside of joint.

With cozy base on the pot, mark cutline for top.
With cozy body on pot, mark cut line for top.

With cozy on pot, slide lid (side) on, leaving lip to cover thickness of top.
With cozy on pot, slide lid on, leaving lip for thickness of top.

Place strip of Reflectix Tape around perimeter of sidewall, leaving 1/2 width of tape exposed.
Place strip of Reflectix Tape around perimeter of cozy, leaving 1/2 of tape strip exposed.

Notch exposed tape with scissors.
Notch exposed edge of tape.

Put top piece in place, pull tape tabs over and fasten to top.
Pull tape tabs over and fasten to top piece.

Your finished Reflectix pot cozy.
You now have a Reflectix pot cozy.


I found that I had to trim the sides of the lid up about a half inch to allow for gripping the bottom, in order to remove to lid.

I weighed the cozy bottom and, just constructed, lid for the SUL1100, it was 1.37 ounces. Smaller pots will have lighter cozies. In comparison, Sara Kirconnell's pint sized cozy weighed 1.27 ounces.

I hope this thread will inspire those teetering on the edge, to get out there and MYOG. It's fun and you'll have fellow backpackers asking where you got that cool stuff.

Edited by redleader on 12/24/2008 13:16:47 MST.

Chris Martin
(hope_for_gorilla) - F

Locale: Finger Lakes
reflectix cozy on 04/02/2012 20:32:23 MDT Print View

Denis, thank you for the excellent and simple tutorial. I just finished mine and I'm quite happy with how it fits.

As shown below, I gave my lid a shorter skirt, because I want to try using the lid as a pot parka on a super cat stove.

Is there any reason to put holes in the lid for steam to escape?

Reflectix pot cozy and 0.9L Vargo titanium pot

Reflectix pot cozy and lid

Denis Hazlewood
(redleader) - MLife

Locale: Luxury-Light Luke on the Llano Azul
Re: reflectix cozy on 04/02/2012 21:00:50 MDT Print View

Chris,

This is the first response I've had to the "Cozy" thread. Good job!

As to the steam hole: I'd leave it out. Escaping steam lowers the pressure and causes a temperature drop. Probably not measurable in our case but there non the less. If your pot lid fits so snugly that it blows off when the pot boils, a hole in the pot lid might be the answer.

Cheers-

Denis

I just noticed your pot has a pouring lip and doesn't seal at all. Ignore the potlid hole comments. I wouldn't vent the cozy at all. I'd put the lid on when done with the fire and let it soak.

J Thomas Peterson
(tpeterson1959) - MLife

Locale: Southwest
Nice on 04/04/2012 23:09:38 MDT Print View

Both of you did a great job. I've made several cozies over the years and even keep oe at my desk at work for cup o' soup and another for my water bottle when I want to keep it cold.

Roger Dodger
(RogerDodger) - F

Locale: Wess Siide
Inspiring on 02/13/2013 20:35:17 MST Print View

Thanks for sharing.
Thumbs Up

Tim Anderson
(tim@bikeswitzerland.com) - F
Reflextix is a magic material, and DIY work can be better than most manufacturers on 02/16/2013 06:50:42 MST Print View

It seems at times that this community over-complexifies design elements in the pursuit of unstated goals.
Usually, the simplest, lightest solutions that actually get used are the best. And most can be done at home.
I've used reflectix for :
- cozies
- stove base (with a small circle of ptfe cookie sheet for the place where the stove is placed to avoid melting)
- combination cozy and windscreen (with cookie sheet in the areas the flame can hit)
- pot holder/cozy
Since manufacturers can't sell us something so obviously simple and cost effective that we could do it at home, we DIYourSelfers tend to think that the solutions we provide are technically inadequate, when they are most likely the most appropriate solutions.
Let's continue to innovate ;) appropriately
Tim

Edited by tim@bikeswitzerland.com on 02/16/2013 07:00:25 MST.

Denis Hazlewood
(redleader) - MLife

Locale: Luxury-Light Luke on the Llano Azul
Re: Reflextix is a magic material, and DIY work can be better than most manufacturers on 02/16/2013 17:55:31 MST Print View

I do this stuff for fun and entertainment. Ergo: everything is appropriate.

Randy Thornton
(Ochocoman)

Locale: Wet side of the Cascades
Tip for sealing the edges on 02/17/2013 21:58:01 MST Print View

Thanks for posting your process - very interesting how you do the tape.

One of things I sometimes do to the edges is seal them closed with some heat instead of using tape. I use the flame from a lighter to heat the bubble between the reflective layers then squeeze it closed. You can get a very clean line this way.

Sealed top edge

One example where I have used this is a cozy for a Glad twist-lock container used as a cup: the cozy edge fits snuggly at the top.

In use

Edited by Ochocoman on 02/17/2013 22:14:11 MST.

Kevin Beeden
(captain_paranoia) - F

Locale: UK
re: Re: Reflextix is a magic material, and DIY work can be better than most manufacturers on 02/18/2013 11:33:19 MST Print View

Denis,

I think Tim was being complimentary...

The only comment I'd make on your instructions compared to the way I did it was to note that you cut triangles out of the tape that hold the base/lid circles in place.

I simply cut down to the centre of the tape, and overlapped the resulting tape tabs.

Yours will be marginally lighter... ;-)

I think a halfway house is probably optimal; cut a V-shaped piece out between each tab so that the edges of the tabs meet perfectly when folded down. The width of the tab and the V-piece could be calculated from the radii of the cosy and width of folded tape. Now I'm making things overly complicated...

Edited by captain_paranoia on 02/18/2013 11:34:05 MST.

Denis Hazlewood
(redleader) - MLife

Locale: Luxury-Light Luke on the Llano Azul
Re: re: Re: Reflextix is a magic material, and DIY work can be better than most manufacturers on 02/18/2013 23:52:25 MST Print View

I think I cut triangles cause it's what I see in the mirror every morning while shaving.

Ian B.
(IDBLOOM) - MLife

Locale: PNW
Jedi taping technique on 02/19/2013 07:25:01 MST Print View

I wish I'd seen this thread before I built my cozy. I ended up using >dozen 1" tabs of tape to put the top and bottom on. It would have been easier and lighter to use what you've shown here. Well done sir.

Eric Blumensaadt
(Danepacker) - MLife

Locale: Mojave Desert
Pot-as-a-dish concept on 02/19/2013 14:00:11 MST Print View

COOL!

I'm a "Freezer Bag" cooker so I use a Velcro-closing fleece bag cozy to hold teh freezer bags for my meals.

Your concept is great for those of the "pot cozy persuasion".

And E
(LunchANDYnner)

Locale: Pacific Northwest
Reflectix on 02/19/2013 15:27:27 MST Print View

I've made freezer bag cozies with reflectix too. It works great. Food stays piping hot during the rest/rehydration time.

Derek M.
(dmusashe) - M

Locale: Pacific Northwest
Where to get Reflectix? on 08/27/2013 02:28:31 MDT Print View

Just curious... Where's the best place to buy this reflectix material? After a cursory look online, it looks like most of the reflectix available is either in the form of a windshield reflector or a large roll.

Does anyone have a good source to recommend where I could buy a small amount of reflectix (as in only a few square feet)?

Thanks for your help!

Ken Thompson
(kthompson) - MLife

Locale: Behind the Redwood Curtain
Re: Where to get Reflectix? on 08/27/2013 06:08:45 MDT Print View

My local Ace Hardware sells it by the foot.

jerry adams
(retiredjerry) - MLife

Locale: Oregon and Washington
Re: Where to get Reflectix? on 08/27/2013 08:33:03 MDT Print View

Home Depot? Lowes?

Roger Dodger
(RogerDodger) - F

Locale: Wess Siide
Re: Where to get Reflectix? on 08/27/2013 11:24:37 MDT Print View

as you noted, the car sunshade bubble foil deflector.
if you are super cheap, try the 99 cents dollar stores.
or try the auto stores, Pep boys, Walmart, Target, Kmart, etc.

Since you will be cutting it up, I recommend you get the sunshade for a large truck's windshield. The cost is about the same, but you get an extra sq ft or two of material.

it doesn't have to be NEW, get the old sunshade from your friend's car, most people have them, people rarely use them, always tucked away under a car seat or the truck.

the roll of tape is under $5 at Home depot
http://www.homedepot.com/p/t/100318556

Edited by RogerDodger on 08/27/2013 11:28:32 MDT.

robert v
(mtnbob123) - F

Locale: Upstate South Carolina
Supply of reflective bubble material on 09/11/2013 08:23:45 MDT Print View

Just a heads up. I have gotten quite a few reflective bubble mailers for free from places that transport insulin. Check with hospitals, or other related industries.

alex hansen
(holden425)
Re: MYOG - Reflectix Pot Cozy on 09/13/2013 00:37:36 MDT Print View

inspired by this thread i finally forked over the 7 bucks for a car window sun shade. BTW, i got mine at walgreens, it was half the price of O'Reilly auto parts. decided to skip the 3 dollar reflectix tape and opted for standard packaging tape
SP700

bottom coozy

whole kit

weight break down:
pot and lid by itself w/ cutouts glued on, 130g
top and bottom coozy by themselves, 24g
whole kit, 154g
whole kit minus lid, 115g

i feel like i may be able to skip the lid since the coozy lid should work just fine as a lid. anyone think it will melt with an esbit tab under the pot?
the lid coozy sits tight over the bottom coozy so i dont need a stuff sack to keep my cookset together.

Edited by holden425 on 09/13/2013 00:40:10 MDT.

Denis Hazlewood
(redleader) - MLife

Locale: Luxury-Light Luke on the Llano Azul
Re: Re: MYOG - Reflectix Pot Cozy on 09/13/2013 05:36:28 MDT Print View

Most likely it will melt, if not burn. The cozy should be built to slide over the pot after it is removed from the stove. The Reflectix system is to keep the pot from cooling so fast, after the stove does its work.

P.S. I really like the red material you used. They don't call me 'Red Leader' for nothing. PM me if you like.

Be safe.

Edited by redleader on 09/13/2013 05:47:00 MDT.