JETBOIL TOUCH DOWN
JETBOIL directly put the pot on the ground.
Able to burn separate type gas burner.
Stable. Light.
http://jp.youtube.com/watch?v=Ayae5VFi4XM

Is also supported by solid fuel.

http://jp.youtube.com/watch?v=R-yPvfStfa0



,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

上のとは、別の物ですが友人に仮の実験として真下からの吸気を全閉させたときの燃焼の様子を観察してもらいました。これはそのときの様子です
http://beyondx.exblog.jp/8746055/

Beyondx
Beyondx

正常な燃焼のようです

Edited by JSBJSB on 05/03/2008 06:44:04 MDT.

JSB,
Good job! I like the solid fuel stand. How much does it weigh?
The videos show your work is a success.
Chris

Crisさん、ありがとう。

固形燃料を燃やす場合に、使ったものはアルミカップを短く加工したものです。
重さは、３８ｇです


JETBOILの下のスキマを２０ｍｍぐらいに設定するとうまく燃えます。

trangiaのゴトク部品、TR-２８１を流用すると簡単に作れそうです。

Edited by JSBJSB on 05/03/2008 08:04:00 MDT.

I can't read Japanese to save my life, but the videos and still photos make me want to build something for use with Esbit and alcohol in case I run out of butane. For some reason, I never bothered to try before now. The Jetboil rests perfectly on a BPL tri-wing solid fuel stand. It also rests on top of a Gram Weenie Pro stove. With no windscreen and using only my body as a shield in a light breeze, an ounce (30ml) of alcohol in the Gram weenie Pro stove was able to bring 2 cups of water almost to boiling. Several bubbles were coming to the top, but it was not a rolling boil. I did take off the neoprene cozy as flames surely would have burned it if I had not removed it. I put it back on immediately after removing from the stove.
If nothing else, it's a good excuse to make a cup of hot chocolate. Also, it a good reminder to grab a windscreen with the stove next time.

For Jetboil users, check out a hacked up "shorty" Jetboil at http://beyondx.exblog.jp/8746055/
I notice the lip is missing, but it does appear to shave about 81 grams (2.85 ounces) off the original weight, including removal of the handle.
I don't use the Jetboil often, usually at work when I'm on job sites or customer sites around the state. It isn't exactly UL, but it's too convenient to ignore some days.

Edited by back2basics on 05/03/2008 11:06:37 MDT.

I have thought of lightening the jetboil. I would cut bits off the steel base under the burner rather than shorten the pot. I usually cook for 2. Steel is much heavier than Aluminium. There is quite large bits that could be cut off without changing the air flow. Jetboil are not really designing for light weight.

Edited by Derekoak on 05/03/2008 11:00:53 MDT.

This is cool. Any other tips for reducing weight on the Jetboil? Thanks, folks.

Very nice work Yukio san.

I always look forward to your seeing your next stove designs.

Tony

A Litehiker Article on lightening a Jetboil

And the translated page from Ezy

Edited by jbrinkmanboi on 05/09/2008 13:27:02 MDT.