BPL Community Profile

Dan Yeruski (zelph) - BPL Lifetime Member

My Locale www.bplite.com
About Me Dan Yeruski has not added a biography yet.
My Website URLhttp://www.bplite.com

You cannot send this user a personal message (PM) because they have not specified a PM email address yet.

All Forum Posts by Dan Yeruski

Showing 41 - 50 of 866 | Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ...87
 

Post

Forum » Thread
Foster can for use with StarLyte burners
I made 4 Foster cans for use with the StarLyte burner when placed under a Caldera-Keg system. No shim is needed. This photo shows the new can on the right. The supporting ridgeline has been relocat...

In Gear Deals » Foster can for use with StarLyte burners
April 25, 7:26pm
Wood Power
Kevin, these videos will give you a better idea of how I vertical stack wood for a longer burning and easier start up. The stove has a lot of area that you can "see" the wood on fire ...

In GEAR » Wood burning stove for a REAL camp fire?
April 25, 7:13pm
Re: HUH??
"I just don't "grasp the concept" of how either the Epicurian or ESBITMISER can control the ESBIT flame and lower it." Eric, here are few vidioes that show how the Esbitm...

In GEAR » ESBIT: Simmering and Ultralight Baking
April 25, 6:33pm
Re: New Foster can for StarLytes
"Do you know when you will have the pot stands back in stock?" Steven, I'll make one up for you tomorrow morning. Go ahead and do the paypal transaction and I'll ship late afte...

In Gear Deals » StarLyte Burner With Cap
April 24, 8:54pm
New Foster can for StarLytes
I made 4 Foster cans for use with the StarLyte burner when placed under a Caldera-Keg system. No shim is needed. This photo shows the new can on the right. The supporting ridgeline has been relocat...

In Gear Deals » StarLyte Burner With Cap
April 24, 8:33pm
Re: Re: Re: Re: Re: Re: Re: Re: Guys any progress?
Based on what I read via the link Christopher gave I decided to insert a catalytic heater into the center of a StarLyte burner to see if it will assist in a more complete burning of fuel. Fuel will...

In GEAR » Alcohol Stove Users Only
April 24, 8:24pm
Re: Epoxy
I suggest you try Oatey Epoxy Putty. Surfaces to be joined should be roughened with sandpaper, emery or file as per directions. Wash hands after use. It's easy to use. Just cut off amount ne...

In Make Your Own Gear » Bonding ALU rods to tubes - What adhesive?
April 24, 9:04am
Re: Yippee!!
Packman Pete, yes, the StarLyte easily fits inside the fosters can. I'll ship yours out today....thank you. . James, I'm overwhelmed by your insight into boiling water and thermodynamic...

In GEAR » Trail Designs stove replacement?
April 24, 8:37am
Re: Re: Re: Starlyte questions
James, That is true, I stand corrected, but. The rate of heat loss due to vaporization is miniscule compared to the amount being produced within the cone. Agree? Before the boil, heat from with...

In GEAR » Trail Designs stove replacement?
April 22, 7:09pm
Re: Wood burning stove for a REAL camp fire?
This stove is made out of stainless steel wire cloth and is easy to assemble and break down. One load of vertical stacked twigs will boil 4 cups of water in a lightweight Kmart grease pot. The stov...

In GEAR » Wood burning stove for a REAL camp fire?
April 22, 6:27pm

All Reader Reviews by Dan Yeruski

Dan Yeruski has posted no reviews.